High performance regenerative shortwave receiver - covering 160m to 16m band - Charles Kitchin, N1TEV

This regenerative shortwave receiver is highly sensitive and selective and it covers the following frequencies: 1.6MHz-4MHz, 3.4MHz-8.5MHz and 6.8MHz-18MHz.
The RF stage amplifier and low impedance input/high impedance output is accomplished with 2N2907 bipolar transistor. The 1Kohm R1a potentiometer is a very effective RF input atenuator.
The audio amplifier stage uses AD745 FET operational amplifier.
The receiver draws less then 12mA using two 9V battery.



Similar receivers:
http://www.w5jh.net/regen.htm
http://www.aa5tb.com/regen.html
http://www.sm0vpo.com/rx/regen2.htm

Notes: published by the ARRL in QEX for Nov/Dec 1998

3955 - 4455 kHz local oscillator (VFO)

This 2 transistor based covers the whole 80m bandwidth (frequencies between 3500 and 4000 kHz).

This Basic Colpitts LC oscillator designed for 80-meter receiver with 455-kHz IF uses zener in supply line to minimize frequency drift. Emitter-follower buffer contributes to stability by isolating oscillator from mixer.
Low-pass filter C13-L2-C14 attenuates harmonics developed in Q3 and Q4.
L1 is Miller 4503 1.7-2.7 uH variable inductor.
L2 is 48 turns No.30 enamel closewound on 1/4-inch wood dowel or polystyrene rod.
Main tuning capacitor C10 can be 365-pF unit with six of rear rotor plates removed.


Q3 and Q4 - 2N4124

D. DeMaw and L. McCoy, Learning to Work with Semiconductors, QST, June 1974, p 18-22 and 72


Reference: www.seekic.com

2255 - 2455 kHz local oscillator (VFO)

This 2 transistor based covers the whole 160m bandwidth (frequencies between 1800 and 2000 kHz). The intermediary frequency is, of course, 455kHz.
The oscillator has good stability, with circuit noise at least 90 dB below fundamental output. Amplifier Q14 provides required +7 dBm for injection into the balanced mixer of the receiver.


C2 - double-bearing variable capacitor, 50 pF
C3 - miniature 30 pF air variable capacitor
CR1 - high speed switching diode, silicon type 1N914A
L18 - 17 to 41 uH slug-tuned inductor, Qu of 175 (J.W. Miller 43A335CBI in Miller S-74 shield can)
L19 - 10 to 18.7 uH slug-tuned pc-board inductor (J.W. Miller 70F103AI)
VR2 - 8.6V, 1W Zener diode
Q13 - MPF102
Q14 - 2N2222A

This 160m VFO schematic is a two-part article in D. DeMaw, His Eminence-the Receiver, QST, Part 1-June 1976, p 27-30 (Part 2-July 1976, p 14-17)


References: www.seekic.com

A simple regen radio for beginners - Charles Kitchin, N1TEV

This simple SW regenerative receiver was presented in QST magazine (issued September 2000), a monthly membership journal of ARRL.


In this version of the receiver, a prototype PC board is used; it is not directly representative of the currently produced board, although they are similar. In this view of the receiver,
the antenna has been removed. The TUNING capacitor is at the left. Immediately behind the capacitor is the coil, L1. Attached between the TUNING capacitor and the VOLUME control potentiometer immediately beneath you can see D1, C4 and R4 as discussed in the text.

Here's a low cost, simple-to-build, portable shortwave receiver. Its design is noncritical and the receiver is easy to get going. With it, you can receive dozens of international shortwave broadcast stations at night - even indoors - using a 39-inch whip antenna. This little radio is perfect for discovering ham-band QSOs, news, music and all the other things the shortwave bands have to offer.

Although this little receiver is quite sensitive, it naturally won't match the performance of a commercial HF rig, and if you've not used a regen before, you'll have to practice tuning the radio - but that's part of the adventure. Most of today's experienced "homebrewers" got their start by building simple, fun circuits just like this one. You'll gain experience in winding a coil and following a schematic. As your interest in radio communication develops, you can build a more complex receiver later.

The little receiver requires only a single hand-wound coil and consumes just 5 mA from a 9-V battery. At that rate, an alkaline battery can provide approximately 40 hours of operation.
The sound quality of this receiver is excellent when using Walkman headphones. The radio can also drive a small speaker. To simplify construction, a low-cost PC board is available from
FAR circuits. You can house the receiver in a readily available RadioShack plastic project box.

Circuit Description


Take a look at the schematic in Figure 1. L1 and C1 tune the input signal from the whip antenna. Regenerative RF amplifier Q1 operates as a grounded-base Hartley oscillator. Its
positive feedback provides a signal amplification of around 100,000. The combination of the very low operating power of this stage, only 30 uW, with the use of a simple whip antenna
makes this receiver easily portable and prevents it from interfering with other receivers located nearby. Regenerative receivers are, after all, oscillators. R2 controls the amount of positive feedback (regeneration). D1 and C4 comprise a floating detector that provides high sensitivity with little loading of Q1. The relatively low back-resistance of the 1N34 germanium diode (don't use a silicon diode here!) provides the necessary dc return path for the detector.

VOLUME control R5 sets the level of detected audio driving U1, an LM386 audio amplifier. C5 provides low-pass filtering that keeps RF out of the audio amplifier. R4 isolates the low-pass filter from the detector circuit when the volume control is at the top of its range. The bottom of the VOLUME control, R5, and pin 3 of the LM386 float above ground so that both inputs of the IC are ac coupled. This allows the use of a 100-k - VOLUME control; this high resistance value prevents excessive loading of the detector. D5 protects the receiver from an incorrectly connected battery.
L1 is wound on a standard 35-mm plastic film can or a 1-inch diameter pill bottle. C1 can be any air-dielectric variable capacitor with a maximum capacitance of 100 to 365 pF. Total frequency coverage varies with the capacitance value used, but any capacitor in that range should cover the 40-meter ham band and several international broadcast bands. If you use a capacitor with a large capacitance range (such as 10 to 365 pF), you'll find that selectivity suffers. That is, it's more difficult to tune in an individual station because there are more stations within the tuning range than when using a capacitor with a smaller capacitance range (such as 10 to 150 pF). Therefore, an optional fine-tuning control (see the inset of Figure 1) is recommended when using tuning capacitors with a wide capacitance range.


Figure 1 — Schematic of the simple regen receiver. Unless otherwise specified, resistors are 1/4-W, 5%-tolerance carboncomposition or metal-film units. Part numbers in parentheses are RadioShack. Equivalent parts can be substituted; n.c. indicates no connection.

C1 - 150 to 350 pF (maximum value) air-dielectric variable capacitor; see text
C2, C3 - 0.001 µF, 50 V (or more) disc ceramic (RS 272-126)
C4, C10, C11, C14 - 0.01 µF, 50 V (or more) disc ceramic (RS 272-131)
C5 - 0.002 µF, 50 V (or more) disc ceramic (use two RS 272-126 connected in parallel)
C6, C9 - 0.047 µF, 50 V disc ceramic (RS 272-134)
C7 - 10 µF, 35 V electrolytic (RS 272-1025)
C8 - 220 µF, 35 V electrolytic (RS 272-1017)
C12, C13 - 47 µF, 35 V electrolytic (RS 272-1027)
C15 - 5 to 10 pF, 50 V (or more) mica (RS 272-120)
D1 - 1N34A germanium diode (RS 276-1123); don't use a silicon diode here.
D2-D5 - 1N4148 or any similar silicon diode (RS 276-1122)
D6 - 1N4003 silicon diode (RS 276-1102)
J1 - 21/8-inch, three-circuit jack (RS 274-246)
L1 — See text.
Q1 - 2N2222A NPN transistor (RSU11328507) or MPS2222A (RS 276-2009)
R1, R3 - 1 k (RS 271-1321)
R2, R5 - 100 k potentiometer, linear taper (RS 272-092)
R4 - 22 k (RS 271-1339)
R6 - 10 (RS 271-1301)
R7 - 150 k (RSU11345287) or use series-connected 100 k (RS 271-1347) and 47 k (RS 271-1342) resistors.
R8 - 100 k audio-taper potentiometer (RS 271-1722); connect so that clockwise rotation increases the voltage at the junction of the potentiometer arm, R9 and C14.
R9 - 1 M (RS 271-1356)
S1 - SPST miniature toggle (RS 275-612)
U1 - LM386N audio amplifier (RS 276-1731)

Misc:
PC board (see Note 1);
39-inch whip antenna (RS 270-1403);
8-pin DIP socket for U1 (RS 276-1995A);
9-V battery clip (RS 270-325); three knobs (RS 274-402A);
project box (RS 270-1806);
#6-32 screws and nuts, rubber feet;
9-V battery, Radio Shack 22-gauge solid hook-up wire.

Note:
RSU items in the RadioShack catalog need to be ordered (delivery in approximately 7 to 10 business days).

Building the Receiver


Finding the Parts
Air-dielectric variable capacitors can be purchased from several suppliers. You can also find them at ham flea markets or salvage one from a discarded AM radio. All the other components
are available from RadioShack and Digi-Key. PC boards are available from FAR Circuits (see Note 1).

Winding the Coil
Some would-be builders are intimidated by the idea of winding a coil. Actually it's quite easy to do. Sometimes, having a second set of hands helps. For the coil winding, use 22-gauge solid-conductor insulated hook-up wire. Before you start winding the coil, drill a mounting hole in the bottom of the film can or pill bottle. Then, drill two small holes in the side of the coil form, near the top, where the winding starts. (By winding from the top of the coil form to the bottom, the winding bottom is kept well above the PC board, preventing any circuit loading that could decrease the receiver's selectivity.) Feed one end of the coil wire through the first hole to the inside of the form, then out through the second. Tie a knot at the point in the wire where it enters the form—this keeps the wire in place and prevents it from loosening later on. Be sure to leave a two to three inch length of wire at each end of the coil
so you can make connections to the PC board. You can wind the coil in either direction, clockwise or counterclockwise. Tightly wind the wire onto the form, counting the turns as you go. Keep the turns close together and don't let the wire loosen as you wind; this takes a little practice. To make the coil tap, wind 11 turns on the coil form. While holding the wire with your thumb and index finger, mark the tap point and remove the insulation at that point. Solder a two to threeinch piece of wire to the tap. Continue winding turns until the coil is finished (13 turns total). Keep the free end of the wire in place using a piece of tape and drill two more holes in the coil form where the winding ends. Feed the wire end in and out of the coil as before and tie a knot at the end to hold the winding in place. When the coil is finished, remove the tape then carefully solder the three wires from the coil (bottom, tap and top) to their points on the PC board keeping the wire lengths as short as possible. For best performance, the floating detector must be wired using short, direct connections. Therefore, these components are not mounted on the PC board. Mount the VOLUME control, R5, close to the TUNING capacitor, C1. Connect D1, C4 and R4 in series between the hot side of C1 (the stator) and the top of the VOLUME control.

Options


Fine-Tuning Control
You can add a fine-tuning control to the receiver using the circuit shown in the inset of Figure 1. D6 functions as a poor man's Varactor (voltage-variable capacitor). As the voltage from FINETUNING control R8 is increased, the diode is reverse biased and its capacitance decreases. This fine-tuning control is cheap and easy to add, but its added capacitance somewhat reduces the maximum frequency range of the receiver. You can compensate for this by removing turns from L1 if necessary.
Two-Band Option
If you'd like a two-band receiver with noncritical tuning, use a 150-pF capacitor for C1 and install a miniature toggle switch with very short leads to add an additional 250-pF fixed-value mica capacitor in parallel with C1. With the capacitor in the circuit, the receiver will then tune the 80-meter band.

Packaging the Radio
The recommended RadioShack project box includes metal and plastic tops. Use the metal top as a large front panel by mounting it to one side of the box using two small screws and nuts through two of the four predrilled holes. Then drill the control mounting holes and mount the three controls and the ON/OFF switch on the metal panel. The radio is easier to operate if you mount the TUNING capacitor and the regeneration (REGEN) control on opposite sides of the front panel. The VOLUME and REGEN controls are best mounted near the bottom of the front panel to keep their connecting wires to the PC board as short as possible. You can use the RadioShack hook-up wire for the VOLUME and REGEN control connections if you twist the wires closely together and keep their lengths very short. Otherwise, use shielded wires for these connections. You can mount the ON/OFF switch last, in any convenient location. Use one of the two remaining holes in the metal front panel to attach a wire connecting the panel to the PC board ground. Attach the PC board and the coil to the bottom of the project box using small screws. Mount the headphone jack on the box rear, close to the PC board and the LM386. Attach the RadioShack 39-inch whip antenna to one of the back corners of the box using a small screw and nut. If you use the RadioShack jack specified for J1 (RS 274-276), connect together pins 2 and 5 and attach that common lead to C8. Ground pin 1 of the jack. If you intend to use a small speaker, connect it between pins 1 and 3. Then, when headphones are plugged in, the speaker will be disconnected automatically.

Testing and Operating the Receiver

Set the VOLUME and REGEN controls to midrange, plug in the headphones, extend the whip antenna, attach the battery and turn on the receiver. You can check to ensure that the audio stage is
functioning by placing a finger on the center lug (wiper) of the VOLUME control and listen for a buzz. If the audio stage is working, adjust the REGEN control until the set produces a sound, indicating that Q1 is oscillating. If Q1 is not oscillating, carefully check the wiring and measure the voltages labeled on the schematic using a high-impedance DVM or multimeter. Common problems are Q1 being wired backwards (emitter and collector connections reversed) and the wires from coil L1 connected to the wrong places on the PC board.
Use two hands when operating the receiver: one for tuning, the other for controlling regeneration. For international broadcast stations or AM phone operation on 40 meters, carefully adjust the REGEN control so that Q1 is just below oscillation. For CW and SSB, increase the REGEN level so that the set just oscillates providing the required local oscillation for these modes. This receiver picks up lots of stations with just its whip antenna, although using a ground connection will greatly reduce any hand-capacitance effects. To pull in more stations during daylight hours, a 10 to 15-foot (or longer) length of insulated hook-up wire can be used as an external antenna. Simply wrap the end of this wire a couple of times around the whip antenna.
If you operate this receiver close to another radio, the regen's 30-uW oscillator might interfere with it. Those who are interested in building a higher-performance regen receiver for serious CW and SSB reception should read my article "High Performance Regenerative Receiver Design". You can also see the project at http://www.electronics-tutorials.com/receivers/regen-radio-receiver.htm

A similar design made by BH1RBG can be found here https://sites.google.com/site/linuxdigitallab/rf-ham-radio/aamazing-regen-receiver.

The PDF file containing everything about this receiver can be found on ARRL website (not available anymore, but archive.org has a backup of it).

Xtaflex 40m VXO regenerative receiver - Michael J. Rainey, AA1TJ


This circuit is based on the Autoflex/Spontaflex receiver designed by Sir Douglas Hall. It turns out that Sir Douglas' clever circuit works well as a one-stage, crystal-controlled (VXO'd) regenerative receiver.

As he explains in his June, 1964 article (thanks Geoff!), the transistor functions as a common-collector radio-frequency (RF) amplifier in which the gain is augmented by regeneration. The high impedance looking into the base helps to reduce the input tank circuit loading. C8 places the collector at RF ground. Demodulation is provided by the Germanium diode at the emitter. The base of Q1 is at ground potential for AF. The parallel combination of C8, T4 and the headphones provide a 15k Ohm collector load resistance (15k + j0 Ohms) at 700Hz. Q1 operates as a common-base amplifier at AF. The circuit may thus be described as a crystal-controlled, regenerative, reflex receiver; or, Xtaflex, for short!

This crystal-controlled regenerative detector is virtually immune to frequency shifts due to hand-capacitance or antenna "swinging." Neither does the frequency pull when receiving strong signals at a low beat note. Here is an audio snippet sampled at the headphone terminals. Please notice how it's possible to tune through zero-beat with a strong, incoming signal without the slightest hint of synchronization (frequency "pulling"). In operation, this circuit "feels" more like a direct-conversion receiver than a straight-regenerative set (of course, a regenerative set is a direct-conversion receiver "at heart").  
The circuit shown in my schematic diagram is built for 40m. I've used it on the 30m band by changing the frequency-sensitive components. In fact, the rock-solid frequency stability of this regenerative receiver will shine progressively brighter as the frequency is raised. What's more, the degree of VXO frequency shift will increase along with the operating frequency. My 40m prototype exhibited a VXO shift of 3kHz. On 30m the shift was 5kHz.

Under crystal control, a stable regenerative receiver for 15, 10 or even 6m appears to be a practical proposition (an RF amplifier placed ahead of the detector will likely prove useful on these higher bands). On these these higher frequencies it may be possible to eliminate the bandpass filter and connect the signal source directly to the C4/C5 node.

Generally speaking, there are a few tricks for obtaining smooth regeneration using modern, high current-gain, transistors. Wes, W7ZOI, recently mentioned a friend of his that builds smooth-operating regenerative detectors from (modern) bipolar transistors by swapping their collector and emitter in order to reduce the current gain. I've been achieving the same results (without needing to swap the emitter - collector) using early, low current-gain, Germanium transistors. The Xtaflex, for example, uses a Philco, 2N504 MADT (Micro Alloy Diffusion Transistor); date-coded, September of 1959. Another example is my Talking Doll, which uses a 2N107 in the regenerative detector.

Charles, N1TEV's well-known bipolar regenerative detector achieves the same end with a 2N2222A, running at an unusually low collector voltage.

Lacking such methods the device transconductance will increase dramatically with collector current; as noted on page two of Ian Hickman's Imp (click-on "PW Imp: I. Hickman," third from the top) receiver article. Ian cleverly linearizes the regeneration control by using a differential-pair in his bipolar transistor-based detector.
I would like to express thanks to my friend, Jim Kearman, KR1S, for re-planting this idea for crystal-controlled regenerative receivers. I happened to be doodling with a Sponatflex receiver when Jim's message arrived, telling of his experiments with crystal-controlled regnerative detectors. Talk about serendipity!

Links/Reference

http://qrp.kearman.com/html/vxoregen01.html  Jim, KR1S's, JFET, VXO regenerative detector

http://home.comcast.net/~phils_radio_designs/  Dee/Mitch-Dyne; the JFET diode is interesting

http://www.io.com/~nielw/3tube_xtal/3tube_xtal.htm  Quartz crystal inside regenerative FB loop

"An Ultra Simple W1AW Receiver," QST Magazine, May 1997, by N1TEV and WU2D

The old website was http://www.aa1tj.com/xtaflex.html

80m Passive Heterodyne Receiver - Michael J. Rainey, AA1TJ


Using a full-size antenna and a reasonably sensitive headphone, this simple switching mixer will produce an amazing abundance of signals on 80m.

I used a 74HC4052 CMOS multiplexer for the simple reason that I found one in my junkbox. Almost any similar CMOS switch capable of working at this frequency would be equally useful. Likewise, the input balun could be wound on virtually any low(ish)-loss, moderately high-permeability core. Aim for a minimum of 20uH, or so, of inductance per winding. I stole the square-wave BFO from my current transmitter which uses a VXO circuit similar to the one used in my Snowflake. Of course, any number of simple square-wave oscillators - built around CMOS or TTL logic gates - would do as well.

4/5/08

Please bear in mind the mixer output impedance is roughly the same as the source impedance; typically, 50 Ohms. Directly coupling a pair of 600 Ohm headphones to the mixer - as I show in the schematic - will result in an insertion power loss of roughly 5dB. There are a number of ways to improve the impedance match to the headphones you choose to use. An audio transfomer between the mixer output and the headphones is an obvious possibility. My solution was to alter the primary/seconday turns-ratio of the input balun transformer in order to raise the mixer working impedance to approximately 600 Ohms. For this, I used a turns-ratio of 1 to 3.5.

In the past ten days I've used this receiver to make a total of twenty contacts on 80m. I particularly enjoyed working Paul, VE1DY, who was running an Elecraft K2 at 4W, and Bill, W9VC, using his Drake 2NT with an output power of 66W.

The 80m square-wave BFO


Construction information

T1: 7 trifilar turns on FT37-43 or Minicircuits T4-1, etc.
IC1: 74HC4052; ground pins are 2,5,6,7,8,14,15
U1 (BFO): 7400 TTL NAND
X1 (BFO): 3.58MHz ceramic resonator
VC1 (BFO): 20-60pF variable capacitor

The old website was http://www.aa1tj.com/80mttldirectconversionreceiver.html

80m TTL ("One Chip") Direct Conversion Receiver - Michael J. Rainey, AA1TJ

This simple receiver is constructed around a single, 7400, Quad-NAND, TTL, integrated circuit. Please don't substitute 74S00, 74LS00, 74HC00, etc., for U1 in this circuit. At a minimum, the biasing would be incorrect for devices other than the "Plain Jane," 7400 IC.

Two gates create a VXO with a square-wave output of sufficient frequency-range to cover most of the 80m CW band.  

The third gate functions as a linear RF amplifier which is enabled or disabled by the VXO signal on U1-pin 9. This switching action creates a simple product detector. Resistors R3 and R4 set the proper bias for linear operation of the enabled amplifier.

L1, C5 and C6 comprise an impedance matching network having a "peaked" lowpass characteristic. This provides a measure of AF bandpass filtering.

The fourth gate acts as a linear AF amplifier. R5 and R6 produce the DC bias needed for linear operation. C7 rolls-off the amplifier response at high frequencies.

Of course, it's possible to use an input bandpass filter other than the one shown in the schematic. The mixer input impedance is approximately 1200 Ohms.

Some oscillator leakage is to be expected using this type of mixer. I measured 6uW of leakage into a 50 Ohm resistor connected to the antenna terminals. Also, I wouldn't advise using this circuit at 40m; I suspect the SWBC bleed-through would be objectionable.

On my first night (April 2, 2008) using this receiver I was pleased to have worked Michel, F5IN, as well as Pat, KØPC. Michel was my first transatlantic DX contact in over 30 years. A few days later I had a message from Pat, saying that he'd looked through his Novice logbook and discovered that we'd met before on the air. On January 3, 1971, Pat (then, WNØZSF) and I (then, WNØDEN) had worked each other on 40m. I'd been using my Ameco AC-1 and Realistic DX-120 station.

Construction information

T1: 10mm, shielded "IF can", 16-turn main winding, 3.5 to 6uH; 1-turn coupling
T2: Ditto above, except 6-turn coupling
U1: Basic 7400 TTL Quad NAND (not 74LS00, 74HC00, etc.)
Ground U1 Pin 7
Measured bias voltage; U1-pin 10 ~1.17Vdc, U1-pins 12/13 1.45Vdc
U1d output impedance ~100Ohms; use transformer matching for other headphone impedance

The old website was http://www.aa1tj.com/80mttldirectconversionreceiver.html

80m ceramic VXO - Alan Yates VK2ZAY



The following schematic has been taken from http://www.vk2zay.net/article/95 article about an VXO 80 metre receiver.
"I started by building a VXO circuit, to see just how far these things could be pulled. It was found to be quite practical to pull them about 100 kHz and still have a stable oscillator, meaning the two available devices could cover most of the interesting parts of 80 meters."

Construction information

The ceramic resonator are 3.58 or 3.68 MHz. The 2 transistors are BC549 used as oscillator and 2N3904 used as buffer.

40m receiver with Polyakov Detector - Michael J. Rainey, AA1TJ


T1,T2, T3: 4uH with adjustable slug, 10mm square, shielded; pry off shield to wind coupling-link over grounded end.
Headphones: 600 Ohm impedance or higher; change AF transformer (10k:500 Ohms), T4, to match phones used.


The old website was https://sites.google.com/site/mjrainey/

80m band pass filter and amplifier - Alan Yates VK2ZAY

The following schematic has been taken from http://www.vk2zay.net/article/95 article about an VXO 80 metre receiver.

Both band pass filter transformers are 455kHz IF transformers that are rewound with 12 turns and 2 turns on the primary and the original capacitor has been removed. The transistor used in the amplifier is a BC549.


Regenerative Receiver for 40 Meters - Rick Andersen KE3IJ (revised 2006)

[I have revised this article as of January 15th, 2006, showing an alternative to the toroid-core inductors of the original design. The revised version uses #26 or #28 enamelled copper 'magnet wire' (such as sold in 3-packs by Radio Shack) wound on McDonalds' plastic straws as coil forms, then covered with molten candle wax to hold the turns in place. See details below.]
I absolutely love regenerative detectors. They amaze me to no end. For those of you who don't know the basics: 99% of all commercially-made radios these days are based on the Superheterodyne design. It has proved itself worthy of universal praise and reliability many times over since it replaced earlier designs in the 1930's. It made Television practical. It will probably always be used as the core of any communications receiver ever built in the future.

But there were earlier beasties that worked well, too, at least for the era in which they lived. The...THE...most sensitive design was the Regenerative circuit. The idea, invented by Major Edwin Armstrong in the 1910's, was to 1) tune in a feeble radio station, 2) amplify it at RF [he used a vacuum tube; we use a transistor today], and, here's the punch-line: 3) feed a small fraction of the amplified signal back to the input, in phase with the incoming antenna signal. A snowball effect occurred, where the signal was reinforced by a boosted version of itself, over and over again -- the precise amount of positive feedback usually held in a delicate balance, right at the edge of the point where the tendency would be to break into a squealing oscillation (like the inevitable feedback howl that your high school principal would experience at the podium microphone when he was getting ready to bawl the student body out about some prank somebody pulled). It is at this threshold that the regenerative detector has unmatched sensitivity (well, the Superregen, covered elsewhere, is actually better, but not as selective).

It was found that this just-before-oscillation setting of the feedback or Regen control was best for listening to AM radio stations; advancing the regeneration any further would cause the station's carrier frequency to be heard as an audio beat note -- a loud squeal -- so your Grandpop would tune in a station with one hand, then set the regeneration to just below oscillation with the other hand. For CW (Morse Code transmissions) or SSB (Single Sideband transmissions) he would leave the regeneration in its oscillating region; the only way to hear the "beep, beep" of a Morse Code signal would be to purposely generate that audio beat note, by "beating" or heterodyning [subtracting the frequencies of] the on-and-off, inaudible CW carrier with an almost-the-same-frequency "fake" carrier generated inside the radio itself... which is what you get when the feedback is past that 'avalanche' point mentioned up above.

So why do we use Superhets nowadays, and why are Regens ancient relics?

Well, because Superhets are free of almost every problem that plagued the earlier types of radios. But we Radio Geeks don't care about the Good Life, do we? We would rather build something that takes a brain surgeon's steady hand and patience to operate, than be hypnotized by the wiles of Madison Avenue! Besides, We built it ourselves!

So be warned: Regens are not "user-friendly" in the convenience-store, modern-day, spoiled-brat, lazy-ass sense. (Yep, I'm soap-boxing again!) Instead, they're fussy little circuits that need re-tweaking and fidgeting as you tune up and down the band.

They're notorious for accidentally re-radiating (transmitting) their own internal RF oscillations back out into the world (when you use a single regen detector stage, directly connected to an antenna. You can solve that problem by putting an RF Amplifier stage ahead of the main detector, which then serves to isolate the antenna from the oscillating detector. The gain of the new stage need not be high, since the Regen stage already has fantastic sensitivity, and you want to avoid overloading it with too strong a signal).

They share, along with another kind of receiver design called the Direct Conversion receiver, an annoying susceptibility to front-end AM overload (you hear your normal stations normally, but at the same time some super-powered station like Radio Moscow or Radio Havana Cuba can be heard simultaneously, all over the dial, even though you're not tuned anywhere near its actual frequency) but, again, this can be improved by adding another stage with another tuned circuit, or else using a resonant bandpass antenna tuner to provide some extra rejection of out of band signals. (The Direct Conversion crowd does it by using what is called a Doubly-Balanced Mixer in the front end; I felt I'd better mention that before they start sending me nasty emails about my ignorance of the new and improved direct conversion designs out there.)

Without the front-end isolation mentioned above, regen receivers will also rock back and forth slightly in tuning frequency as the wind blows your antenna wire back and forth outside -- very annoying if you're listening to a single sideband voice signal or CW.

If you don't build 'em with at least some metal ground plane or shielding in the box, you'll notice that body capacitance can be a problem: the tuning shifts when you reach for the tuning knob! (A similar effect with nearby metallic objects led to the development of metal detectors; one man's problem is another man's solution!)

And, most annoying to me, but not mentioned too often in other articles about the regen, is that the tuning changes when you advance the regeneration into oscillation. So if you build your own Shortwave radio using a regenerative detector, and attempt to calibrate its tuning dial (I paste a piece of semicircular paper on the front panel and make pencil markings), you will find that the tuning is 'off' when you're listening to CW or sideband, from when you calibrated the dial for AM, just before the point of oscillation.

Well, not a true Electronics Geek / Radio Head. We love this little circuit because it's almost magic. It can dredge the weakest signals almost out of thin air due to the ingenious application of controlled positive feedback. We just need to be able to control it, that's all! If you're a Generation-Xer, but have been bitten by the Bug (why else would you still be reading this page, you sadist!?), know that your Grandpappy loved, cherished, and relied on his Homebrew "Genny"; your Dad (my age) at least built a few of these as "toy" kits sometime during the 1950's - 1970's, and a spate of articles in QST and other Amateur Radio publications appeared in the 1990's, especially by Charles Kitchin, that revived the old Regen for a new generation of tinkerers, with some new bells and whistles added to smooth out some of the bugs that Regens were known to have.

I guess I've waxed eloquent enough.

My 40 Meter Regenerative Receiver

Here's a schematic of my version of the trusty old Regen radio. The heart of it is Q2, where I use a common JFET (Field Effect Transistor), an MPF102, in a modified Armstrong "tickler coil" design where I supply feedback from the "bottom"-- the Source of the JFET -- rather than the usual top -- the Drain of the FET. Works just as well either way.
The tuned circuit is set up for the 40 meter Ham band -- approx. 7.1 - 7.35 MHz in this radio.



Simple regenerative Radio Receiver by Rich Bonkowski – W3HWJ

Charles Kitchin has written many articles about regen radios for QST and other hobby magazines. I like his approach to design and have had good luck with his circuits. The first attempt at a "Kitchin" used a printed circuit board that I bought from Far Circuits. This was an excellent learning tool and prompted me to continue experimenting and changing the design and the circuit board.

To house this project, I "re-purposed" a metal container that originally contained Christmas cookies. After drilling the mounting holes for all the controls, I used a bit of steel wool to create a matte finish, cleaned with mineral spirits, and then spray painted. The labels for the controls were made with a Brother P-touch labeler. Thanks to Dave Schmarder, N2DS, for getting me interested in the Brother. It makes a nice laminated label that is good-looking, sturdy, and solidly adherent.

By changing the plug-in coil, I can cover 3.5 to over 10 MHz. It's a bit difficult to copy SSB signals as the detector is not super stable, but it works well enough! I made a few mistakes in this version, such as mounting the speaker on the side of the case. It needs to be on the front or the top cover to direct sound toward the listener. Also, using a large value main tuning capacitor proved to be a problem, even though I used an 8:1 reduction dial. The vari-cap "fine tuning" is definitely needed to copy SSB successfully!

Things I learned:

  • For drilling large holes in thin sheet steel, a stepped drill bit (Uni-bit) is very helpful. The Harbor Freight Tools version is cheap but serviceable. 
  • Spraying a lacquer "clear coat" over a not-fully-cured enamel paint job can cause an un-intended "wrinkle" finish. You can't see the cover in these photos. 
  • Designing and making your own pc board is challenging and educational. I learned about ExpressPCB software, blue Press 'n Peel transfer film, and using peroxide and muriatic acid to etch boards. I also found that the toner used by Brother laser printers doesn't work as well as HP toner for making etching masks using Press 'n Peel film. 
  • PVC plumbing pipe and fittings make good coil forms when used in conjunction with bases salvaged from defective radio tubes. This design uses a 6-pin tube base. At most ham swap meets, I can buy dead 6-pin tubes for 25 cents.

The RF stage is using an 2N2222 bipolar transistor, the regenerative detector an N-Channel RF MPF102 transistor and the audio amplifier a LM386 IC.

This receiver has been taken from http://www.w3hwj.com/index_files/HBradioweb.html website.

Super-regenerative Air Band Radio 108MHz-136MHz - Pilar Ortega

Civil aviation still uses AM communications between 108MHz and 136MHz. It is fairly easy to build a receiver that operates on these frequencies, however, it will also be found easy to build a receiver that won’t tune high enough! The trick to getting the tuning range high enough is to use a high frequency transistor and VERY short leads. I used a BF199 transistor but a 2N2369 will probably work well too.
By far the most reliable construction method is ‘ugly’ construction on a 1 inch by 2 inch piece of copper clad board (I built this circuit on perforated board many years ago and it only just tuned high enough to receive my local airport signals). By using the copper foil as a ground plane we can mount components in mid air. This is more robust than it might seem because many components connect to decoupling capacitors that provide an anchor to the board. Keeping leads short reduces stray inductance and capacitance, and helps ensure stability and good tuning range. The circuit is based on an old one advertised in a hobby magazine many years ago, modified slightly.

The tuning coil "L" is simply four turns of 0.8mm diameter wire with a diameter of 5mm. There is no former. The coil is compressed or expanded to adjust the tuning range. We need to arrange that we can just tune the upper end of the FM broadcast band when the tuning potentiometer is at minimum setting (wiper at the ground end). This will bring the Air Band into the main tuning range of the receiver. The antenna is a short telescopic one and couples with a ¾ turn link turn. Note that, if the coupling is too tight (the link too close to the main coil) then the regenerative stage will be too loaded and won’t oscillate.
The varicap diode ‘D’ was an unmarked component in my receiver, however, the BV409 should work admirably here. All capacitors with the exception of the electrolytic are ceramic. The transistors are best mounted upside down with their leads bent sideways.
No switch was used in my receiver. Instead, a stereo 3.5mm socket was used and the third contact used to switch the supply. Note that this trick only works when a mono plug is inserted! I mounted the earphone socket such that it traps the battery in one corner of the case. I expect this apparently cool solution is going to come back to bite me when I drop the radio, and the socket gets smashed off by the momentum of the battery!
In operation the regeneration control is increased until a rushing sound is heard. This noise indicates that the circuit is oscillating but will diminish when a signal is received. At this time the tuning and regeneration potentiometers can be adjusted for best reception. The receiver will be found to be most sensitive when the regeneration is set so that the circuit is just oscillating.
Purists will add an RF gain stage prior to the regenerative section, as this minimises coupling of oscillations to the antenna as well as adding sensitivity. In practise the circuit is sensitive enough but one should be aware that RF radiation from the antenna can interfere with nearby equipment, in particular, televisions.

This receiver has been taken from http://geopodium.com/files/Pilar/index.htm website, which is currently unavailable. Apparently the new homepage is http://techlib.com, but this receiver is no longer posted on the new website.